Roofing in Miami-Dade and Broward

Foam Set vs. Mechanically Fastened Tile Roofs in Miami-Dade and Broward: What's the Difference?

Updated November 21, 2026 Reviewed by Brandon Vega, owner, Apex Roofing Solutions Corp. (license CCC1336242)
Concrete tile roof seen from above with ridge tiles, valleys and a gutter along a stucco wall in Weston, FL
Apex Roofing Solutions job in Weston, FL

A foam-set tile roof uses an approved foam adhesive to bond the tiles to the underlayment, the protective layer beneath them. A mechanically fastened tile roof uses hardware to secure the tiles. Which option fits your Miami-Dade or Broward home depends on the approved combination of products and the wind pressures the roof must resist. Apex Roofing Solutions Corp. offers a free inspection with no obligation, and we get on the roof every time. We put every price and fee in writing before work starts and tie payments after signing to city permit approval and passed inspections.

Key takeaways

  • Miami-Dade County's Product Control checklist lists TAS 101 for mortar or adhesive attachment and TAS 102 and TAS 102(A) for mechanical attachment without and with a clip, respectively.
  • The Florida Building Commission identifies Miami-Dade and Broward as the two counties in the High Velocity Hurricane Zone.
  • Miami-Dade Notice of Acceptance 26-0514.07 gives one product-specific example of foam attachment and requires a current tile assembly approval that lists uplift resistance with that adhesive.
  • Apex's November 11, 2026 planning range for installed concrete tile is $9.75 to $11 per square foot. Your existing roof, underlayment, chosen system and roof complexity affect the job price.
  • Apex charges a $500 deposit at signing for a home, then 35% of the balance at permit approval, 35% after the in-progress inspection passes and 30% after the final inspection passes.

What actually holds each tile in place?

With foam-set tile, the adhesive makes the connection between the tile and the underlayment. With mechanical attachment, hardware makes the connection that holds the tile in place. Miami-Dade County's roof tile approval checklist treats these as different attachment methods and lists separate tests for adhesive attachment and mechanical attachment.

The attachment method describes a part of the roof you can have a roofer point out in the manufacturer's installation details. With foam, ask to see where the adhesive contacts the underside of the tile and the surface below it. With mechanical attachment, ask the roofer to point to the hardware and show what it connects to. If the contractor proposes a clip, ask which detail shows that clip for the tile you're buying.

The county checklist also calls for installation details for valleys, hips, ridges and roof penetrations when a manufacturer submits a tile system for approval. A valley is where two roof slopes meet and form a channel. Hips and ridges are raised lines where slopes meet. A roof penetration is an opening for something like a vent. If a roofer shows you only a drawing of tiles in the middle of a slope, ask to see how the proposal handles those other parts of your roof.

Which attachment can handle the wind on my house?

Either attachment method can work if the approved tile assembly's tested uplift resistance meets the wind pressure calculated for your roof. Uplift is the force that tries to pull roofing upward. The Florida Building Commission places both Miami-Dade and Broward in the High Velocity Hurricane Zone, or HVHZ.

Miami-Dade's Product Control checklist points to Roofing Application Standards RAS 118, 119 and 120 for tile installation. Miami-Dade County's Product Approval Notices say the 9th Edition of the Florida Building Code takes effect December 31, 2026. The Florida Building Commission's analysis of changes for the 2026 edition identifies RAS 118 and 119 with mechanically fastened tile systems and RAS 120 with mortar and adhesive-set tile application. The analysis describes RAS 127 as the procedure for evaluating tile roof resistance for a building of a specified roof slope and height. Roof slope is how steep the roof is.

The same analysis describes TAS 106 as a field verification procedure covering both adhesive-set tile and mechanically attached rigid roof coverings. In the section on how many tiles to test on the roof, the 9th Edition uses the ASCE 7 names Zone 1, Zone 2 and Zone 3.

What would a foam adhesive approval show me?

A foam adhesive approval shows the conditions under which that particular adhesive can be used. For example, Miami-Dade Notice of Acceptance 26-0514.07 covers DAP StormBond Roof Tile Adhesive and its Low GWP version. A Notice of Acceptance, or NOA, is a Miami-Dade County product approval document that spells out how the listed product can be used.

The DAP approval covers approved flat, low, medium and high tile profiles, meaning the shapes of the tiles. It calls for a current NOA for the tile assembly that lists uplift resistance with that adhesive. It also limits use to roofs where the project's required pressure stays within the design values obtained using the RAS 127 calculations. If a proposal names this foam, ask for the tile assembly approval alongside the foam approval. Then ask the roofer to show you where the two documents connect.

The DAP document also calls for a factory-trained qualified applicator approved and licensed by DAP. It specifies where the adhesive goes and the minimum amount for different tile profiles. The tile must be set in fresh adhesive within four minutes of dispensing it. These are conditions for the named DAP products. If your proposal names a different adhesive, ask to see the conditions in that product's approval and how the installer will follow them.

What should a mechanically fastened tile bid identify?

Ask for the exact tile, the proposed fasteners and the approval detail that shows the hardware for your installation. If the bid includes clips, ask where they appear in the detail. Miami-Dade's checklist lists TAS 102 for mechanical attachment without a clip and TAS 102(A) for mechanical attachment with a clip.

Ask whether the proposed assembly uses battens, which are strips the tiles can sit on. Then have the roofer show you how the fasteners reach the roof sheathing, the wood surface beneath the roofing layers. The Florida Building Commission's 2026 change analysis describes 9th Edition revisions to RAS 118 and 119 calling for roof tile fasteners to penetrate three-quarters of an inch into the sheathing even when battens are used. The analysis summarizes revisions. Ask the contractor which edition and approval details apply to your permit and where they specify fastener penetration.

Get the exact underlayment product in writing, too. The Commission's analysis describes 9th Edition changes to RAS 118, 119 and 120 requiring underlayment systems to be tested and have product approval for use as tile roof underlayment. If one bid says only 'mechanically fastened tile,' ask the contractor to fill in the tile name, the hardware detail and the underlayment before you compare the two totals.

How do I tell what I am paying for in each tile bid?

Put the two bids next to each other and compare the tile assembly and the scope of work before judging the price difference. If one bid uses foam and the other uses fasteners, identify any other differences at the same time. Start with the tile model, then check the underlayment and the approvals each contractor names.

As of November 11, 2026, Apex's planning range for installed concrete tile is $9.75 to $11 per square foot. The existing roof, the underlayment, the system you choose and the complexity of the roof move the price. On a 22-square roof, that range works out to $21,450 to $24,200 for planning. One roofing square is 100 square feet of roof surface, so this example uses 2,200 square feet of roof. That is a concrete tile planning range. Your written quote comes after we inspect your roof and price the work.

Next, look at what each bid includes from tear-off through final inspection. Check how each contractor lists the permit fee. Find the unit prices for wood that may need replacement. Read the written workmanship warranty and ask what manufacturer warranty comes with the proposed system. If you still see a price gap, ask each roofer to point to the specific difference in the products or scope that explains it. You can book a free inspection with Apex by calling 305-290-2482.

What can Apex tell me before recommending a tile replacement?

We get on your roof, take photos and show you what needs attention and what is cosmetic. The inspection helps us decide whether a repair makes sense or whether to quote a replacement. If a repair fixes the problem for less than the roof has left to give, we quote the repair.

If a replacement makes sense, we show you up to three roof system options with written prices and the monthly financing figures. For an Apex tile replacement, we tear off the old roof down to the wood deck and install an NOA-approved system with a named underlayment. We handle the permit and both city inspections. Ask us to show you where the proposal identifies the tile assembly, how the tiles will be attached and which approval applies.

The photos also give you a way to follow the recommendation while you're looking at the proposal. If your concern is one area of the roof, ask us to show you what we found there and explain how it affects the scope. For a replacement, Apex provides a written 10-year workmanship warranty at completion, plus a manufacturer warranty where the system has one. Manufacturer warranties depend on installation to the manufacturer's specifications.

How will Apex price a tile roof and bill me?

Apex prices your roof after the on-roof inspection and writes the scope, fees and payment terms into the contract. For a home, you pay a $500 deposit at signing. The remaining balance is divided across city permit approval and the two city inspections, so you can see which milestone goes with each payment.

You pay 35% of the balance when the city approves the permit. Another 35% of the balance is due after the in-progress inspection passes. The final 30% of the balance is due after the final inspection passes. The contract lists the permit fee. If you want to compare financing with paying out of pocket, the quote shows the monthly financing amount. The quoted price holds for 30 days.

One part of the bill may depend on what we find after the old roofing comes off. The contract gives you a price per sheet or per foot, as applicable, for rotten wood deck, fascia and soffit. Fascia is the board along the roof edge, and soffit is the surface underneath the overhang. We charge only for what we actually replace. If you're comparing foam and fastener bids and want to know what your own roof calls for, call 305-290-2482 to book a free inspection with Apex Roofing Solutions Corp. We are based in Miami Lakes and serve Miami-Dade and Broward. Our Florida roofing license is CCC1336242.

Questions homeowners ask

Is foam-set tile the same as adhesive-set tile?

Foam-set tile is a type of adhesive-set tile. For example, Miami-Dade NOA 26-0514.07 identifies DAP StormBond as a polyurethane foam roof tile adhesive tested under TAS 101. Ask for the exact adhesive name and the approval for the tile assembly it will be used with.

Does a foam approval tell me whether I can use it with the tile I picked?

Check the tile assembly approval alongside the adhesive approval. For example, the DAP StormBond NOA calls for a current tile assembly NOA that lists uplift resistance with that adhesive. The DAP approval also limits use to projects whose required pressures are within the calculated design values.

Can I choose the attachment method just by looking at two bids?

Ask each roofer to show how the proposed assembly fits your roof's design wind pressures. Compare the exact tile, attachment detail and underlayment on both bids. Then check the scope and written terms so you can see what accounts for the difference in price.

Do I still need the underlayment name if the bid gives me the tile model?

Ask for both names. The tile model tells you which tile the roofer priced. The underlayment name identifies the product beneath it. With a foam-set assembly, it also tells you the surface the roofer is proposing to bond the tile to. Ask the contractor to show how the underlayment fits the approved installation.

What does Apex charge at signing, and when is the rest due?

Apex prices residential roof replacement after the free inspection. The deposit is $500 at signing. Of the remaining balance, 35% is due at city permit approval, 35% after the in-progress inspection passes and 30% after the final inspection passes. Financing is available, with the monthly amount shown on your quote.

Sources

Free Estimate

Tell Us About Your Roof

Share a few details and our team will follow up with the next step.

  • Roof repairs, replacements, and inspections
  • Tile, shingle, metal, and commercial roofing
  • Serving Miami-Dade, Broward, Palm Beach and Monroe counties

Prefer to talk to a person?

Call now if you need help today.

305-290-2482