To get a roof or reroof permit in Coral Springs, start with the Broward County Building Permit Application. You’ll also need the city’s Zoning Addendum. The other document is the Roofers Application Packet, which tells you which forms and attachments go with your roof type. The Coral Springs Building Department checklist calls for the job value and product approvals. The city says other requirements may apply, so use that checklist as a starting point for your address. For a residential replacement, Apex Roofing Solutions Corp. offers a free roof inspection. We put every fee in your written contract. We also handle the permit and both city inspections. After the $500 signing deposit, your payments are tied to permit approval and the two passed inspections.
Key takeaways
- Start with the three application documents on Coral Springs Form 013.0. That form also calls for the job value and product approvals.
- For every reroof, Coral Springs Form 013.1 calls for the Owner Notification for Roofing Considerations.
- If you’re getting shingle or metal, your roofer uses Sections A, B and D of the Uniform Permit Application. For tile, Section E is where the calculations go.
- If the job is valued over $5,000, the city checklist calls for a Notice of Commencement before your first inspection.
- At Apex, we put the permit fee in your written replacement contract. You pay $500 at signing. The balance is due in 35%, 35% and 30% payments tied to permit approval and passed inspections.
Which three documents do you need to start a Coral Springs roof permit?
Start with the Broward County Building Permit Application. You’ll also need the Building Permit Application Zoning Addendum. The other document is the Coral Springs Roofers Application Packet. Those are the three application documents listed on the city’s Roof / Re-Roof Permit Application Checklist, Form 013.0, revised October 26, 2026. That checklist also lists structural and zoning review.
Put the job value on the application. The city may also ask for an itemized cost breakdown. Form 013.0 lists product approvals and the Statement of Responsibility Regarding Asbestos. It also lists paperwork for installing lightweight concrete when applicable. Ask your roofer to walk you through which items they’re submitting. If the job covers a sloped main roof and a low slope addition, ask them to show you both areas in the written scope and on the roof sketch.
If your contractor hasn’t registered with Coral Springs yet, Form 013.0 lists the registration requirements. The form also lists an Owner/Builder Affidavit Packet if you’re applying as the builder. If you hire Apex for a residential replacement, we pull the permit. We’re a Florida Certified Roofing Contractor based in Miami Lakes, licensed and insured under CCC1336242. Whoever you hire, ask whose name will go on the application. Keep a copy with your contract.
What should you be able to point out on your roof sketch?
You should be able to point to each level and section of your roof on the sketch, including any low slope area your roofer is replacing. Section B of the city’s Uniform Permit Application asks for the dimensions. It asks for drains and wall outlets too. Your roofer also has to show the raised edges, called parapets, and give the dimensions of the areas that face higher wind pressures.
You’ll find the Uniform Permit Application in the city’s Roofers Application Packet, Form 013.1. Form 013.1 calls for the application on every roofing permit it describes. It references the 8th Edition (2023) Florida Building Code and its High Velocity Hurricane Zone requirements. Those are the hurricane building rules cited in Form 013.1. Section A records the job address and the contractor. It also records the roof category and the type of work. That’s where the square footage for the roof areas goes.
Check the address first. Then ask your roofer to show you where the work starts and stops on the sketch. Let’s say the proposal includes new shingles over the main house and work over the back room. Ask which area is entered as steep slope. Ask which is entered as low slope. Then check how each area is described in the price. If you have another contractor’s proposal, compare the roof areas each one covers before you compare the totals.
Which paperwork changes for shingle, metal, tile or low slope roofs?
The instructions for Form 013.1 tell you which sections to use for your roof. Asphalt shingle and metal roofs use Sections A, B and D. Concrete or clay tile uses A, B, D and E. A low slope application uses A, B and C. Each roof category has its own list of attachments, so ask your roofer to show you the row for the roof you’re buying.
For a steep slope roof, Section D asks who made the product and what its Notice of Acceptance number is. A Notice of Acceptance, or NOA, is a product approval document. It tells you how an approved product or system can be used and what limits apply. When the instructions call for product approval pages, they list the cover page and the specific system description. They also list the specific and general limits and the applicable drawings. Ask to see the pages for the system on your proposal. The details show how your roofer is proposing to install it.
If you’re getting tile, Section E of Form 013.1 calls for calculations that show how the attachment can resist wind trying to lift the tiles. Form 013.1 directs your roofer to use Method 1 or 2 for systems rated on resistance to turning force. Method 2 is limited to Broward County Exposure C. Form 013.1 directs your roofer to Method 3 for systems rated on upward pulling force. Ask which method they used and where you can see the attachment they priced.
For a low slope roof, Section C asks who makes the system and what its approval number is. It also asks about the roof deck, which is the surface that supports the roofing. The roofer has to describe the layers and how the system is fastened. If you have a low slope addition, ask which system is going on that part of the house and how the proposal covers the spot where it meets the sloped roof. In an Apex residential replacement proposal, look for the name of the underlayment, which is the layer beneath the finished roof covering. Look for the approval for the roof system too.
What are you initialing before a reroof in Coral Springs?
Your initials show that your roofer explained an item to you. The city’s Roofers Application Packet calls for the Owner Notification for Roofing Considerations on every reroof at permit time. On page 2, Section 1524.1 says the roofing contractor explains the notice. The form has signature lines for the owner or agent and the contractor.
The city’s form covers refastening the existing wood deck, which means fastening that wood again. It covers exposed ceilings. It also covers overflow wall outlets. When your roofer explains the refastening, ask which wood they expect to leave in place and how the proposal prices any damaged wood that has to come out. If you have an open beam ceiling and can see the underside of the wood, bring it up before you sign. The notice explains that you can ask to preserve the way the ceiling looks. Talk through how your roofer would handle nails that might show from below.
An overflow scupper is an opening through a wall that lets water out. The form explains that a wall around your roof can block drainage, so overflow outlets may be needed. If your roof has walls around it, ask your roofer to point out the outlets on the roof plan. Then ask whether the written scope includes work on those outlets. When you review the quote, you’ll have a place to check what you discussed.
What else should your roofer check on your house?
Ask your roofer to check the color and material you’re choosing. Have them check any equipment on your roof. Also ask them to check the connections between your roof and your walls. Coral Springs lists preapproved colors and materials on Form 013.0. The form also lists a Rooftop Mounted Equipment Affidavit when applicable. It also lists Broward County Board of Rules and Appeals Formal Interpretation #28, Retrofitting Roof to Wall Connections.
Start with the equipment you recognize. If you have a solar roof fan, roof vents or skylights, the city checklist calls for applicable product approvals. Form 013.1 specifically covers approval for vents and skylights. Ask your roofer to show you what the quote says about your existing equipment and which approvals go with the items on the application. If you’re picking a color or changing materials, have your roofer check your choice against the city’s list before you settle on it.
On pages 11 and 12 of Form 013.1, the Roofing Affidavit for Windstorm Loss Mitigation asks the contractor’s qualifying agent to certify which of three conditions applies. If the existing roof anchors comply, the form points to photos. If a roof connection upgrade is required, it points to an application and design or plans. If an exception applies, it points to supporting records for that exception. If your roofer says the house needs connection work, ask which condition applies and where that work is written into the proposal.
What has to happen before your first inspection and final approval?
If the job value is over $5,000, Coral Springs lists the Notice of Commencement on Form 013.0 as due before the first inspection. Keep track of that document separately once the permit is moving. Ask your roofer when it’ll be ready and how you can get a copy.
During installation, Form 013.1 calls for a cap sheet inspection for every deck type described in Form 013.1. On a tile roof, the calculations go in with the application. Then Form 013.1 calls for a tile uplift test before final approval. Ask your roofer how those steps fit your job and when you’ll see the inspection results.
Keep the permit number handy during the job. Once the work is done, ask for the final inspection result and confirm that the permit is closed. Save that record with your contract and warranty. If you see two different dates on the paperwork, have your roofer point out the date the permit was approved and the date of the final inspection. Those two events also mark different payments on an Apex replacement.
Where can you check the price for the permit and any extra wood?
Look for the permit fee in your written price. At Apex Roofing Solutions Corp., we put it in the residential replacement contract with the price for the roof we inspected and quoted. We write down what we charge per sheet or per foot for rotten deck wood, fascia or soffit. You pay those rates only for the material we actually replace.
The worry I hear from homeowners is that the price could go up when the old roof comes off. Some of the wood can be hard to judge until then. The deck is the wood surface under the roofing. The fascia is the board along the edge of the roof. The soffit is the underside of the overhang. Ask your roofer where the rates are written and how they’ll show you how much wood they replaced. At Apex, we take photos of the replaced wood so you can see what the charge covers.
On an Apex residential replacement, you pay $500 when you sign. You pay 35% of the balance when the city approves the permit. Another 35% is due after the inspection during installation passes. The last 30% is due after the final inspection passes. If you’re considering financing, look for the monthly amount on your written quote. When the job is complete, you get our 10-year workmanship warranty in writing. You also get the manufacturer warranty where the system has one. That warranty depends on installation to the manufacturer’s specifications.
If you’re deciding between repair and replacement, you can book a free roof inspection or call Apex at 305-290-2482. We get on the roof and show you photos of what needs work and what’s cosmetic. If a repair makes sense, we can quote it. If replacement makes sense, we can explain the roof options. We can show you the permit fee and the wood rates. We can also walk you through when each payment comes due.
Questions homeowners ask
Can I bring a paper roof permit application to Coral Springs?
The city’s Form 013.0 says the Building Department stopped processing paper submittals on January 1, 2026. The same form says the city will take your paper documents, convert them to electronic format for a fee and give the papers back to you. You’ll find the directions for the online portal in the checklist.
Do shingle and metal roofs need the same paperwork in Coral Springs?
Both use Sections A, B and D of the Uniform Permit Application. The difference is in the attachments. The city’s Form 013.1 lists Attachment 3 for metal roofs. That’s where the design calculations go. The asphalt shingle row leaves Attachment 3 off its list. Both rows list Attachment 7 for any required roof testing or calculation documents.
Do I need to include skylights in the Coral Springs roof permit application?
Yes, when applicable. The city checklist includes skylights among the items that need product approvals. The Roofers Application Packet says components such as skylights and roof vents must have a Notice of Acceptance, which is a product approval, at permit time. Ask your roofer to show you which skylights are in the proposal and which approval applies.
Is the $5,000 threshold for the Notice of Commencement a permit fee?
Look at the value of the job. That’s what the city uses the $5,000 threshold for on Form 013.0. For a job valued over $5,000, Coral Springs lists the Notice of Commencement as required before the first inspection. We list permit fees separately in your written Apex replacement contract.
What do I pay Apex when Coral Springs approves my roof permit?
You pay 35% of the balance when the city approves the permit for an Apex residential roof replacement. Before that, you pay $500 at signing. After the inspection during installation passes, you pay another 35%. The final 30% is due after the final inspection passes. We price your roof after the free inspection. If you’re considering financing, we show the monthly payment on your quote.
