If you're within 3,000 feet of a saltwater coastline, the 9th Edition Florida Building Code, which takes effect December 31, 2026 according to Miami-Dade Product Control, adds corrosion protection requirements for the roof fasteners and metal connectors it covers. For exterior parts that are partially sheltered or openly exposed, Table 1711.1 calls for stainless steel at 300 feet or less. Beyond 300 feet through 3,000 feet, that same row calls for galvanizing on fasteners and enhanced galvanizing on connectors and plates. The row applies to those two exposure conditions. Section 1711.1 exempts fasteners and connectors that are fully embedded in concrete or mortar. At Apex Roofing Solutions Corp., we offer free roof inspections in Miami-Dade and Broward. We put every price and fee in writing before work starts. We tie residential replacement payments to permit approval and city inspections.
Key takeaways
- Section 1711 of the 9th Edition Florida Building Code covers fasteners and connectors within 3,000 feet of a saltwater coastline. It exempts those fully embedded in concrete or mortar. Miami-Dade Product Control identifies December 31, 2026 as the effective date of the 9th Edition.
- At 300 feet or less, Table 1711.1 calls for stainless steel for the covered exterior parts that are partially sheltered or openly exposed.
- Beyond 300 feet through 3,000 feet, Table 1711.1 calls for galvanized fasteners and enhanced galvanized connectors and plates for those same exposures.
- Within 3,000 feet of a saltwater coastline, Section 1711.1.1.3 requires a covered fastener's corrosion-resistant metal or coating to be compatible with the corrosion-resistant metal or coating of the connector or plate it touches.
Which parts of your roof does Section 1711 cover?
Section 1711 of the 9th Edition Florida Building Code covers fasteners and metal connectors within 3,000 feet of a saltwater coastline. Fasteners hold materials in place. Those include screws, bolts or nails. Connectors and metal plates are what join parts together. The Florida Building Commission's Significant Changes document explains that the protection those parts need depends on how far they are from the coast and how exposed they are to salty air.
Miami-Dade Product Control identifies December 31, 2026 as the effective date of the 9th Edition. If you're getting quotes now and expect the work to carry over into the new edition, ask the office issuing your permit which edition it will use to review your project. Then ask your roofer to use that answer when they write out what the job includes.
Section 1711.1 makes an exception for fasteners and connectors fully embedded in concrete or mortar. If your roofer uses that exception in a bid, ask them to show you which pieces will be completely surrounded by concrete or mortar once they're installed.
What changes if you're more than 300 feet from the shoreline?
The material requirements change at 300 feet for exterior parts that are partially sheltered or openly exposed. At 300 feet or less, Table 1711.1 calls for stainless steel for the listed fasteners and for the connectors or plates. Beyond 300 feet through 3,000 feet, that same row calls for galvanized fasteners and enhanced galvanized connectors and plates.
Section 1711.1.1.2 sets one set of criteria for fasteners above 3/8 inch in diameter and a different set for those 3/8 inch or smaller. It also lists ways to show that the smaller fasteners resist corrosion. If the proposal just says 'galvanized screws,' ask your contractor which screws they're using and which criterion those screws meet.
Ask your roofer which table row applies and what shoreline distance they used for the bid. If you're close to either cutoff, ask the permitting office how it wants that distance documented. Keep that answer with your proposal so you can check whether both bidders worked from the same information.
What should your roofer show you when a screw goes through a metal plate?
Ask your roofer to name the fastener and the plate together. Section 1711.1.1.3 requires the fastener's metal or coating to be compatible with the connector or plate it touches. When different metals touch, they can corrode through an interaction the code calls galvanic action. Once your roofer has named both parts, they have something specific to check.
When we compare proposals, we start by looking for the exact roof system and the name of the underlayment, which is the layer under the roof covering you see. We also look for the Notice of Acceptance, or NOA, which is the document that shows the product approval. For a coastal job, ask your contractor where the hardware they're proposing appears in the approval or installation documents. Then ask how those parts meet the corrosion requirements for your address.
Before you sign, you can ask each bidder the same question. Which fasteners and connectors come with this price, and what document shows they fit my roof? That lets you compare what you're getting for each of the two prices. If you're still unsure whether your roof needs work, you can book a free roof inspection. We'll get on the roof, take photos and show you what we see in the photos of your roof.
Where will I see the coastal hardware in my Apex price?
We price each residential replacement after we've inspected the roof. If the work includes coastal hardware, ask us to name it in the written scope so you can compare what's included in your bid. We write every price in the contract before work starts. That goes for every fee and every term, too. Financing is available, and the quote shows the monthly payment.
If you're worried the bill will go up once the old roof comes off, look at the unit prices in the contract. Those are the prices per sheet or per foot. We list them for rotten roof decking, fascia and soffit. Decking is the wood surface under the roofing. Fascia is the board along the edge of the roof. Soffit is the underside of the overhang. We charge only for what we replace.
For residential replacement, you pay $500 when you sign. You pay 35% of the remaining balance when the city approves the permit. The next 35% is due after the in-progress inspection passes. The final 30% is due after the final inspection passes. If you'd like a free inspection for a roof in Miami-Dade or Broward, call Apex Roofing Solutions Corp. at 305-290-2482.
Questions homeowners ask
Do I need stainless steel within 3,000 feet of the coast under the Florida Building Code?
For partially sheltered or openly exposed exterior parts, Table 1711.1 specifies stainless steel for the listed fasteners and for connectors and metal plates at 300 feet or less. Beyond 300 feet through 3,000 feet, that same row calls for galvanized fasteners and enhanced galvanized connectors and plates. Ask your roofer to confirm which exposure condition applies to the parts in your proposal.
What if my home is exactly 300 feet or exactly 3,000 feet from the coastal shoreline?
If you're exactly 300 feet away, Table 1711.1 puts you in the closer band. Exactly 3,000 feet is still in the band that starts beyond 300 feet. If your property is near either cutoff, ask the permitting office how it wants you to document the distance.
Can measuring how far I am from the coast tell me if I need a new roof?
Section 1711 is about protecting the hardware from corrosion. To see whether repair or replacement makes sense for the roof you have, we get on the roof and take photos. Then we show you which findings need work and which are cosmetic.
Is my Apex roof inspection free, and when would I pay for a replacement?
The roof inspection is free. We price residential replacement after we've inspected the roof. You pay $500 at signing. You pay 35% of the remaining balance when the city approves the permit. Then you pay 35% after the in-progress inspection passes. The last 30% is due after the final inspection passes.
