South Florida Roofing News

What does the Florida 9th edition drip edge rule mean for your 2027 roof in Miami-Dade or Broward?

Updated November 18, 2026 Reviewed by Brandon Vega, owner, Apex Roofing Solutions Corp. (license CCC1336242)
Gray tile roof with hips and eaves seen from above in Weston, FL
Apex Roofing Solutions job in Weston, FL

If the 9th edition applies to your 2027 roof permit and your project falls under the High Velocity Hurricane Zone rules, Section 1517.6.2.3 calls for drip edge at the bottom edges of the roof and along the sloped edges of the gables. Drip edge is the metal trim that directs water off your roof, and this rule applies to roofs with the slope specified in that section. The Florida Building Commission’s summary puts the metal over the protective layer under the roof covering. It allows a specific exception for qualifying self-adhering underlayment over primed metal. Miami-Dade County lists December 31, 2026, as the effective date. Ask the building department that issues your permit to confirm which edition applies and which detail your roof needs. At Apex Roofing Solutions Corp., we offer a free roof inspection and put the price and every fee in writing. After the signing deposit, we tie residential replacement payments to permit approval and passed city inspections.

Key takeaways

  • Miami-Dade County lists December 31, 2026, as the effective date of the 9th edition. Ask the building department that issues your permit which edition applies to your roof.
  • Section 1517.6.2.3 names the eaves and gable edges. Have your roofer show you both on your roof drawing.
  • The Florida Building Commission’s summary allows self-adhering underlayment that meets ASTM D1970 to go over a primed drip edge flange.
  • The 4-inch fastening figure comes from the statewide asphalt shingle summaries. Ask your roofer to show you the fastening detail for your permit and roof system.

Which roof edges should your roofer point out on the permit drawing?

Ask your roofer to show you the eaves, which are the lower edges where rain runs off. Then have them point to the gable edges, which are the sloped edges at the end of the house. The Florida Building Commission’s Building analysis names both in its summary of the new High Velocity Hurricane Zone provision, Section 1517.6.2.3.

The commission’s summary of Section 1517.6.2.3 gives a roof slope of 2:12. That means the roof rises 2 inches for every 12 inches measured horizontally. If your roof has sections with different slopes, like a sloped main roof and a porch that slopes less, have your roofer mark the slope and show you the detail for each area included in the work.

What goes down first at the roof edge?

The Florida Building Commission’s summary of Section 1517.6.2.3 puts the drip edge over the underlayment. Underlayment is the protective layer under the shingles, tile or other roof covering. The section allows self-adhering underlayment that meets ASTM D1970 to go over a primed drip edge flange. The flange is the flat part of the metal that sits on the roof.

Ask your roofer to name the underlayment and show you where the metal sits on the drawing. If the drawing puts the underlayment over the flange, ask which product meets ASTM D1970 and where the drawing specifies the primer. When two proposals both say they meet code, that gives you something specific to compare.

Where does the 4-inch fastening figure come from?

The Florida Building Commission’s statewide asphalt shingle summaries list mechanical fastening at 4 inches on center. That’s the distance from the center of one fastener to the center of the next. The Building analysis gives the spacing in Section 1507.2.9.3 and sends you to Section 1507.2.6 for the fasteners. The Residential analysis gives the spacing in Section R905.2.8.5 and refers to Section R905.2.5.

In that same Residential analysis, tile has its own provision, Section R905.3.8.1. It calls for drip edge on slopes of 2:12 and greater and points to the FRSA/TRI Florida High Wind Concrete and Clay Roof Tile Installation Manual. Ask your roofer to show you the High Velocity Hurricane Zone detail that applies at your address and the fastening schedule for the roof system on your quote.

What should you check if your roof permit carries over into 2027?

First, ask the building department that issues your permit which edition applies to your application. Miami-Dade County’s Product Approval Notices list December 31, 2026, as the effective date of the 9th edition. If you sign in December or already have an application in the system, give the department your application number if you have one and ask them to confirm the edition.

Then ask your roofer which Notice of Acceptance goes with your proposal. A Notice of Acceptance, or NOA, is a Miami-Dade product approval document. The county says the 9th edition changes affect some existing roofing underlayment approvals. Have your roofer show you which approval goes with the underlayment they named and where to find the drip edge detail in the permit documents.

Where can you find the roof edge work in your Apex proposal?

Before you sign, ask us to point out the drip edge work in the written scope. At Apex Roofing Solutions Corp., we get on the roof and show you photos of what we found before we price your residential replacement. We put every price in writing before work starts. That includes every fee and every term. Your proposal names the underlayment and the roof system.

If you’re worried the bill could go up once the old roof comes off, have us walk you through the wood prices in your contract. The deck is the wood surface under your roof covering. If we replace any of it, we price it by the sheet. Fascia is the board along your roof edge, and soffit is the underside of the overhang. We price fascia or soffit replacement by the foot. You pay only for what we actually replace.

For a residential replacement, you pay $500 when you sign. When the city approves the permit, you pay 35% of the remaining balance. The next 35% is due after the in-progress inspection passes. The last 30% is due after the final inspection passes. If you’re considering financing, we show you the monthly payment on the quote.

Call 305-290-2482 to book a free roof inspection. If you already have a proposal or permit record, keep it handy and we can go through what the contractor put in writing for your roof edge.

Questions homeowners ask

What does 2:12 tell you about the slope on your roof detail?

Your roof rises 2 inches for every 12 inches you measure horizontally. Have your roofer show you which edges of your roof the Section 1517.6.2.3 detail covers.

Does the code summary let the underlayment go over the metal?

Yes. The Florida Building Commission’s summary of Section 1517.6.2.3 allows self-adhering underlayment that meets ASTM D1970 to go over a primed drip edge flange. The flange is the flat part of the metal that sits on the roof.

Can you use the statewide 4-inch spacing rule to check your roof bid?

The Florida Building Commission lists 4 inches on center in its statewide asphalt shingle summaries for Sections 1507.2.9.3 and R905.2.8.5. Ask your roofer to show you the fastening detail that applies to your roof and permit.

What does Apex charge for a roof replacement, and when do you pay?

We give you a price for your residential replacement after a free inspection. You pay $500 when you sign. You pay 35% of the remaining balance when the permit is approved. The next 35% is due after the in-progress inspection passes. The last 30% is due after the final inspection passes. The contract shows the permit fees and the unit prices for any wood replacement.

Sources

Free Estimate

Tell Us About Your Roof

Share a few details and our team will follow up with the next step.

  • Roof repairs, replacements, and inspections
  • Tile, shingle, metal, and commercial roofing
  • Serving Miami-Dade, Broward, Palm Beach and Monroe counties

Prefer to talk to a person?

Call now if you need help today.

305-290-2482