Our advice at Apex: start with the exact roof system, the named underlayment and the complete Notice of Acceptance documents when you check Miami-Dade NOA requirements for a roof. Then ask the contractor to explain how the scope and installation limits fit your house. Miami-Dade County's SOPREMA component NOA shows that a component approval alone does not establish approval of the complete roof assembly. The examples below help you read those documents; they do not establish which assembly fits your particular roof. At Apex Roofing Solutions Corp., we offer a free inspection, put every fee in writing and tie residential payments to permit approval and passed city inspections.
Key takeaways
- Our advice at Apex: match the document to the proposed roof. Miami-Dade County NOAs accept the products or assemblies they describe within their stated conditions.
- Use the 6 document checks below. Compare the product identity and scope. Check the deck and slope. Review the underlayment and attachment. Check the pressure limits. Get the complete dated documents.
- Miami-Dade County's SOPREMA component approval calls for use within approved roofing system assemblies.
- Miami-Dade County's Sil-Flex approval describes a maintenance coating and expressly limits its use as a roof or waterproofing system.
- Apex takes $500 at signing. Payments of 35%, 35% and 30% of the balance follow at permit approval and passed inspection stages.
What does Miami-Dade actually accept in an NOA?
The document needs to describe what your contractor proposes to install. An NOA is a Notice of Acceptance issued by Miami-Dade County Product Control. It describes an accepted product or roofing assembly and sets conditions for its use. Start with the description. Then read the scope. Also read the limitations. The county's name on the document does not replace those details.
For example, the county's Snap-Clad approval describes aluminum panels over a wood deck. A deck is the supporting surface beneath the roof materials. The Englert Series 2000 approval describes steel panels over a steel deck. Both concern metal roofing, but that does not make the installations they describe interchangeable.
These documents say the described products were designed to comply with the Florida Building Code, including the High Velocity Hurricane Zone, or HVHZ. However, that statement comes with the rest of the document's conditions. The specified deck still matters. The fastening requirements still apply. So do the assembly limitations.
Start your quote review with this question: Which exact acceptance documents describe the roof you are proposing for my house? Before you compare prices, have the contractor connect the product names on the proposal to those documents.
Which 6 document checks should I make before signing?
Put the proposal beside the complete approval documents and make these six checks. You are checking whether what you are buying matches what the documents describe. You do not need to design the roof yourself. The contractor needs to show you where the proposed installation fits.
1. Match the product identity. Compare the manufacturer and exact product name on the proposal with the NOA. A description as broad as metal roofing leaves important details unresolved. The county's Snap-Clad example identifies aluminum panel thickness and a panel width range.
2. Read the approval category and scope. Check whether the document accepts a component or a roofing system assembly. The SOPREMA example is a component approval. The Snap-Clad example is a roofing system approval.
3. Match the deck and roof slope. Slope means how steep the roof is. The Snap-Clad assembly describes wood deck and a slope of at least 2 inches of rise for every 12 inches across. Have the contractor explain how that matches your house.
4. Identify the underlayment and attachment details. Underlayment is the layer beneath the roof covering. Ask for the exact product name. Then have the contractor show you the applicable underlayment provisions and fastening details in the assembly documents.
5. Review the pressure limits and limitations. Ask which assembly applies to your roof. Then ask how its limits compare with your project's design requirements. Even when the product name matches, read the limitations.
6. Check the dates and document completeness. Review the approval date and expiration date. Ask for every page, including tables and drawings. The cited county NOAs require the entire document to be available at the job site when the Building Official requests it.
Why can a component approval leave part of the answer missing?
A component approval may establish properties of one part without describing the complete installed roof. A component is one part of a roof assembly. Miami-Dade County's SOPREMA membrane and accessory NOA makes the distinction directly: its products are designed for use as specified within approved roofing system NOA assemblies.
That document says it establishes physical property testing and traceability for the listed components. Its limitations also require installation in strict compliance with applicable codes. Product approvals must be followed. So must manufacturer specifications. Finding a product name in that document does not settle the rest of the roof design.
The SOPREMA limitations explain that its listed products may be used with an approved roof assembly NOA that lists them as components. Where they are not listed, the document describes a route for requesting approval with supporting documentation. That condition needs to be resolved with the contractor and reviewing authority.
Have the roofer show you the assembly document that connects the proposed components. If all you get is another product brochure, that connection still needs explaining. At Apex, our advice is to have the exact roof system stated in the proposal. Have the named underlayment stated there too. Also have the applicable NOAs stated in the proposal.
How can two metal roof NOAs describe different installations?
The supporting deck and fastening arrangement can differ between metal roof approvals. Even one NOA can contain multiple assemblies with different limits. The county's Englert Series 2000 document separates 18-inch and 14-inch steel panel assemblies over steel deck. So you need the assembly designation alongside the NOA number.
The Snap-Clad example describes aluminum panels over wood deck. Its approved assembly identifies deck thickness provisions for new construction and reroofing. It also gives underlayment options and panel attachment details. If a proposal uses that approval, it needs to identify an installation that fits those provisions.
The Englert example describes a steel deck and gives separate instructions for its two panel widths. If someone hands you a metal roof approval without explaining the deck underneath your existing roof, those are useful details to ask about.
Ask this plain question: Which page describes the supporting deck and panel configuration you priced for me? Then have the contractor identify the proposed underlayment. Keep the answer with your quote so a later material substitution can be checked against the same documents.
What should I ask about wind pressure and fastening tables?
Have the contractor identify the assembly first, then explain how its pressure limits meet your project's design requirements. A pressure number is incomplete without its conditions. The county's Snap-Clad and Englert approvals contain tables that connect pressure limits to fastening arrangements and different areas of the roof.
The roof field is the main area away from the edges. The approval tables also identify perimeter and corner areas. Read their fastening provisions with the applicable assembly and limitations. They are not a single instruction for every roof.
The Englert approval shows why the largest number does not give you the whole answer. Its 18-inch panel assembly states a maximum uplift pressure of negative 62.5 pounds per square foot. The 14-inch assembly has a separate table with additional pressure and clip spacing information. Those figures apply to their specified configurations.
Both metal approvals restrict extrapolation, meaning extending the listed results beyond what the document permits. You should not have to decide whether a proposed fastening change is acceptable. Have the contractor document the applicable arrangement and explain any unresolved question to the reviewing authority before installation.
Can an approved coating be sold as a complete new roof?
Check what the coating approval actually covers before accepting that description. Miami-Dade County's Sil-Flex Silicone Roof Coating NOA approves it as a roof maintenance coating. Its first limitation says the listed product is not approved as a roof system or waterproofing system required by Florida Building Code Chapter 15 HVHZ.
That limitation applies to this specific product approval. It does not make a statement about every coating on the market. However, it shows why an NOA number alone cannot tell you whether a proposal is for maintenance or a replacement roof.
The same document excludes application over several roof coverings, including asphalt shingles and cement or clay roofing tile. It also requires factory trained and certified applicators who follow the manufacturer's published instructions. Having an NOA does not remove those conditions.
If you are comparing a coating proposal with a tear-off replacement, have each contractor state the actual scope. Apex's residential replacement scope includes full tear-off to the wood deck and a new roof system. Before choosing either approach, book a free roof inspection so the recommendation starts with the roof's condition.
What do approval dates and missing pages mean for my quote?
Ask for all pages and have the contractor address the approval dates against your project schedule. The cited county NOAs state that they are not valid after their expiration dates. They also require the complete document to be available for inspection at the job site when requested by the Building Official.
The cited SOPREMA document displays an August 4, 2027 expiration date. The Sil-Flex document displays July 4, 2028. Those dates apply to those particular acceptance documents. They do not tell you how long a finished roof will last.
Missing pages can leave out the information you need most. In the SOPREMA example, the limitations are on the last page. In the metal roof examples, the assembly instructions and pressure tables come after the opening description. If you read only the cover, you miss those conditions.
Apex's residential permit timeline is about 2 to 4 weeks after signing, followed by a firm installation date. Keep the approval questions tied to that sequence. If the proposed product changes while the permit is being prepared, ask for an updated written scope and the documents supporting the replacement selection.
How does Apex connect the specified roof to the written price?
At Apex Roofing Solutions Corp., we price a residential replacement after an on-roof inspection and write every fee and term before work starts. You should be able to identify the roof system and named underlayment in the proposal. Compare the applicable NOAs too, so you understand what the price buys.
The first worry is money: Are two roofers pricing the same installation, and what could change after tear-off? Start with the product names. Then check the wood terms. Rotten wood deck, fascia and soffit are priced per sheet or per foot in our contract and charged only for what is actually replaced.
For a home, our deposit is $500 at signing. You then pay 35% of the balance when the city approves the permit. Another 35% is due after the in-progress inspection passes. The remaining 30% is due after the final inspection passes. We list permit fees in the contract.
Financing is available with the monthly number shown on the quote. A quoted price holds for 30 days. Our residential replacement includes a written 10-year workmanship warranty, plus a manufacturer warranty where the system has one. Manufacturer warranty coverage depends on installation to the manufacturer's specifications.
Our inspection decides whether repair or replacement makes sense. If a repair fixes the problem for less than the roof has left to give, we quote the repair. If replacement makes sense, we show you up to three roof systems side by side, starting with the least expensive option.
Call 305-290-2482 to book a free roof inspection with no obligation. We get on the roof and show you your own photos. We separate what needs fixing from what is cosmetic. Bring your existing proposals so you can ask clear questions about the system and its approval documents before choosing.
Questions homeowners ask
What does NOA mean on my roofing proposal?
NOA means Notice of Acceptance. Miami-Dade County Product Control issues these documents for the products or assemblies they describe, subject to the conditions they state. Ask for the complete document. Then have the contractor explain which part of your proposed roof it covers.
Does a product NOA approve my whole roof?
Start by reading its scope. Miami-Dade County's SOPREMA component NOA says its membranes and accessories are intended for use within approved roofing system assemblies. That component document alone does not identify the complete assembly proposed for your house.
Can I compare roof approvals using the pressure on the first technical page?
You need the assembly details that go with that number. Miami-Dade County's Englert Series 2000 approval has separate provisions for 14-inch and 18-inch panels over steel deck. Have the contractor identify the applicable assembly, then explain how its pressure limits compare with your project's requirements.
Does an NOA expiration date tell me when my roof will wear out?
The expiration date is about the acceptance document. Each cited NOA says it is not valid after its stated expiration date. Those statements do not establish a roof's service life or warranty term. Ask the contractor how the approval dates fit your project schedule.
How does Apex charge for a residential roof replacement?
We price each job after an inspection and put the fees in writing. You pay $500 at signing. Then you pay 35% of the balance at city permit approval. Another 35% is due after the in-progress inspection passes, and 30% is due after the final inspection passes. Rotten wood deck, fascia and soffit have contract prices per sheet or per foot and are charged only for what is actually replaced. Financing is available with the monthly payment shown on the quote.
Sources
- Miami-Dade County SOPREMA roofing membrane and accessory component NOA, with assembly-use limitations
- Miami-Dade County Sil-Flex Silicone Roof Coating NOA, with maintenance-coating scope and limitations
- Miami-Dade County Snap-Clad aluminum panel over wood deck roofing system NOA
- Miami-Dade County Englert Series 2000 steel panel over steel deck roofing assembly NOA
